Complaints & Recalls
Official Safety Recalls - Important!
1 RecallThese are official manufacturer recalls ordered by NHTSA for safety defects. If you own this vehicle, contact your dealer immediately for free repairs.
Nissan North America, Inc.
Safety Issue:
Nissan North America, Inc. (Nissan) is recalling certain 2020-2021 Nissan Armada and 2020-2021 INFINITI QX80 vehicles equipped with V8 engines. The impeller can swell and bind within the fuel pump module, causing it to fail.
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Mfg Campaign: R21A2, R21A3
Recall Date: May 20, 2021
Consumer Complaints
9 ComplaintsNissan North America, Inc.
Defect Description:
SERVICE BRAKES
Potential Consequences:
The brakes automatically engage without cause. The problem occurs at both city and highway speeds, from 20-75 mph. It is particularly bad when passing underneath a bridge. The car will abruptly stop. This has been ongoing for monthes. Sometimes, the vehicle will act inappropriately when the brake is applied by the driver. The car will attempt to accelerate. Other times the car will hard brake as if slamming the brakes.
Corrective Action:
The brakes automatically engage without cause. The problem occurs at both city and highway speeds, from 20-75 mph. It is particularly bad when passing underneath a bridge. The car will abruptly stop. This has been ongoing for monthes. Sometimes, the vehicle will act inappropriately when the brake is applied by the driver. The car will attempt to accelerate. Other times the car will hard brake as if slamming the brakes.
Additional Notes:
The brakes automatically engage without cause. The problem occurs at both city and highway speeds, from 20-75 mph. It is particularly bad when passing underneath a bridge. The car will abruptly stop. This has been ongoing for monthes. Sometimes, the vehicle will act inappropriately when the brake is applied by the driver. The car will attempt to accelerate. Other times the car will hard brake as if slamming the brakes.
Mfg Campaign: 11582054
Recall Date: Apr 10, 2024
Nissan North America, Inc.
Defect Description:
FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING
Potential Consequences:
The brakes automatically engage without cause. The problem occurs at both city and highway speeds, from 20-75 mph. It is particularly bad when passing underneath a bridge. The car will abruptly stop. This has been ongoing for monthes. Sometimes, the vehicle will act inappropriately when the brake is applied by the driver. The car will attempt to accelerate. Other times the car will hard brake as if slamming the brakes.
Corrective Action:
The brakes automatically engage without cause. The problem occurs at both city and highway speeds, from 20-75 mph. It is particularly bad when passing underneath a bridge. The car will abruptly stop. This has been ongoing for monthes. Sometimes, the vehicle will act inappropriately when the brake is applied by the driver. The car will attempt to accelerate. Other times the car will hard brake as if slamming the brakes.
Additional Notes:
The brakes automatically engage without cause. The problem occurs at both city and highway speeds, from 20-75 mph. It is particularly bad when passing underneath a bridge. The car will abruptly stop. This has been ongoing for monthes. Sometimes, the vehicle will act inappropriately when the brake is applied by the driver. The car will attempt to accelerate. Other times the car will hard brake as if slamming the brakes.
Mfg Campaign: 11582054
Recall Date: Apr 10, 2024
Nissan North America, Inc.
Defect Description:
FORWARD COLLISION AVOIDANCE: WARNINGS
Potential Consequences:
The brakes automatically engage without cause. The problem occurs at both city and highway speeds, from 20-75 mph. It is particularly bad when passing underneath a bridge. The car will abruptly stop. This has been ongoing for monthes. Sometimes, the vehicle will act inappropriately when the brake is applied by the driver. The car will attempt to accelerate. Other times the car will hard brake as if slamming the brakes.
Corrective Action:
The brakes automatically engage without cause. The problem occurs at both city and highway speeds, from 20-75 mph. It is particularly bad when passing underneath a bridge. The car will abruptly stop. This has been ongoing for monthes. Sometimes, the vehicle will act inappropriately when the brake is applied by the driver. The car will attempt to accelerate. Other times the car will hard brake as if slamming the brakes.
Additional Notes:
The brakes automatically engage without cause. The problem occurs at both city and highway speeds, from 20-75 mph. It is particularly bad when passing underneath a bridge. The car will abruptly stop. This has been ongoing for monthes. Sometimes, the vehicle will act inappropriately when the brake is applied by the driver. The car will attempt to accelerate. Other times the car will hard brake as if slamming the brakes.
Mfg Campaign: 11582054
Recall Date: Apr 10, 2024
Nissan North America, Inc.
Defect Description:
VISIBILITY/WIPER
Potential Consequences:
While waiting in a parking lot, I was reviewing the settings available on the lower center display, one of those options was for "Camera." Inside this menu I found and made adjustment for options like brightness, contrast, tint, color, and black level... and while most of those seemed to work well, and I was able to make suitable adjustments to the camera--the tint and color options seemed to have no effect on the image. So, I opted to adjust tint from the default/middle value all the way to the left/lowest value and save the settings. Even then, with that saved, I was able to switch to the camera and could see there was no difference in the image still. I then remained with the vehicle, still parked with the engine idling, waiting another ten minutes or so before preparing to leave. When I put my vehicle in reverse gear, I was shocked to see that the camera displays had gone completely black. I could no longer see the rear images when backing up. I tried going back to park and again to the rear setting--still, there was no image being displayed for the cameras. I could see some items on-screen still, like the button to switch camera views and to toggle the parking sensors on/off. When switching camera views/angles, the system would continue displaying the same two black/empty displays. I tried turning the engine off and back on--but that didn't seem to have any effect, the system remained broken. I was able to use the rear view camera on the reviewer mirror--but the normal backup cameras remained non-functioning. I promptly tried opening the camera settings again to reset all of the brightness, contrast, tone, color, and black level settings to the default values... but still, the preview area was black and no image could seen. I've verified the outside of the vehicle... these cameras are not blocked at all. There was nothing that could've cause these to go dark. I drive the vehicle home (~5 miles), and found the camera still not to be working.
Corrective Action:
While waiting in a parking lot, I was reviewing the settings available on the lower center display, one of those options was for "Camera." Inside this menu I found and made adjustment for options like brightness, contrast, tint, color, and black level... and while most of those seemed to work well, and I was able to make suitable adjustments to the camera--the tint and color options seemed to have no effect on the image. So, I opted to adjust tint from the default/middle value all the way to the left/lowest value and save the settings. Even then, with that saved, I was able to switch to the camera and could see there was no difference in the image still. I then remained with the vehicle, still parked with the engine idling, waiting another ten minutes or so before preparing to leave. When I put my vehicle in reverse gear, I was shocked to see that the camera displays had gone completely black. I could no longer see the rear images when backing up. I tried going back to park and again to the rear setting--still, there was no image being displayed for the cameras. I could see some items on-screen still, like the button to switch camera views and to toggle the parking sensors on/off. When switching camera views/angles, the system would continue displaying the same two black/empty displays. I tried turning the engine off and back on--but that didn't seem to have any effect, the system remained broken. I was able to use the rear view camera on the reviewer mirror--but the normal backup cameras remained non-functioning. I promptly tried opening the camera settings again to reset all of the brightness, contrast, tone, color, and black level settings to the default values... but still, the preview area was black and no image could seen. I've verified the outside of the vehicle... these cameras are not blocked at all. There was nothing that could've cause these to go dark. I drive the vehicle home (~5 miles), and found the camera still not to be working.
Additional Notes:
While waiting in a parking lot, I was reviewing the settings available on the lower center display, one of those options was for "Camera." Inside this menu I found and made adjustment for options like brightness, contrast, tint, color, and black level... and while most of those seemed to work well, and I was able to make suitable adjustments to the camera--the tint and color options seemed to have no effect on the image. So, I opted to adjust tint from the default/middle value all the way to the left/lowest value and save the settings. Even then, with that saved, I was able to switch to the camera and could see there was no difference in the image still. I then remained with the vehicle, still parked with the engine idling, waiting another ten minutes or so before preparing to leave. When I put my vehicle in reverse gear, I was shocked to see that the camera displays had gone completely black. I could no longer see the rear images when backing up. I tried going back to park and again to the rear setting--still, there was no image being displayed for the cameras. I could see some items on-screen still, like the button to switch camera views and to toggle the parking sensors on/off. When switching camera views/angles, the system would continue displaying the same two black/empty displays. I tried turning the engine off and back on--but that didn't seem to have any effect, the system remained broken. I was able to use the rear view camera on the reviewer mirror--but the normal backup cameras remained non-functioning. I promptly tried opening the camera settings again to reset all of the brightness, contrast, tone, color, and black level settings to the default values... but still, the preview area was black and no image could seen. I've verified the outside of the vehicle... these cameras are not blocked at all. There was nothing that could've cause these to go dark. I drive the vehicle home (~5 miles), and found the camera still not to be working.
Mfg Campaign: 11534464
Recall Date: Jul 25, 2023
Nissan North America, Inc.
Defect Description:
UNKNOWN OR OTHER
Potential Consequences:
While waiting in a parking lot, I was reviewing the settings available on the lower center display, one of those options was for "Camera." Inside this menu I found and made adjustment for options like brightness, contrast, tint, color, and black level... and while most of those seemed to work well, and I was able to make suitable adjustments to the camera--the tint and color options seemed to have no effect on the image. So, I opted to adjust tint from the default/middle value all the way to the left/lowest value and save the settings. Even then, with that saved, I was able to switch to the camera and could see there was no difference in the image still. I then remained with the vehicle, still parked with the engine idling, waiting another ten minutes or so before preparing to leave. When I put my vehicle in reverse gear, I was shocked to see that the camera displays had gone completely black. I could no longer see the rear images when backing up. I tried going back to park and again to the rear setting--still, there was no image being displayed for the cameras. I could see some items on-screen still, like the button to switch camera views and to toggle the parking sensors on/off. When switching camera views/angles, the system would continue displaying the same two black/empty displays. I tried turning the engine off and back on--but that didn't seem to have any effect, the system remained broken. I was able to use the rear view camera on the reviewer mirror--but the normal backup cameras remained non-functioning. I promptly tried opening the camera settings again to reset all of the brightness, contrast, tone, color, and black level settings to the default values... but still, the preview area was black and no image could seen. I've verified the outside of the vehicle... these cameras are not blocked at all. There was nothing that could've cause these to go dark. I drive the vehicle home (~5 miles), and found the camera still not to be working.
Corrective Action:
While waiting in a parking lot, I was reviewing the settings available on the lower center display, one of those options was for "Camera." Inside this menu I found and made adjustment for options like brightness, contrast, tint, color, and black level... and while most of those seemed to work well, and I was able to make suitable adjustments to the camera--the tint and color options seemed to have no effect on the image. So, I opted to adjust tint from the default/middle value all the way to the left/lowest value and save the settings. Even then, with that saved, I was able to switch to the camera and could see there was no difference in the image still. I then remained with the vehicle, still parked with the engine idling, waiting another ten minutes or so before preparing to leave. When I put my vehicle in reverse gear, I was shocked to see that the camera displays had gone completely black. I could no longer see the rear images when backing up. I tried going back to park and again to the rear setting--still, there was no image being displayed for the cameras. I could see some items on-screen still, like the button to switch camera views and to toggle the parking sensors on/off. When switching camera views/angles, the system would continue displaying the same two black/empty displays. I tried turning the engine off and back on--but that didn't seem to have any effect, the system remained broken. I was able to use the rear view camera on the reviewer mirror--but the normal backup cameras remained non-functioning. I promptly tried opening the camera settings again to reset all of the brightness, contrast, tone, color, and black level settings to the default values... but still, the preview area was black and no image could seen. I've verified the outside of the vehicle... these cameras are not blocked at all. There was nothing that could've cause these to go dark. I drive the vehicle home (~5 miles), and found the camera still not to be working.
Additional Notes:
While waiting in a parking lot, I was reviewing the settings available on the lower center display, one of those options was for "Camera." Inside this menu I found and made adjustment for options like brightness, contrast, tint, color, and black level... and while most of those seemed to work well, and I was able to make suitable adjustments to the camera--the tint and color options seemed to have no effect on the image. So, I opted to adjust tint from the default/middle value all the way to the left/lowest value and save the settings. Even then, with that saved, I was able to switch to the camera and could see there was no difference in the image still. I then remained with the vehicle, still parked with the engine idling, waiting another ten minutes or so before preparing to leave. When I put my vehicle in reverse gear, I was shocked to see that the camera displays had gone completely black. I could no longer see the rear images when backing up. I tried going back to park and again to the rear setting--still, there was no image being displayed for the cameras. I could see some items on-screen still, like the button to switch camera views and to toggle the parking sensors on/off. When switching camera views/angles, the system would continue displaying the same two black/empty displays. I tried turning the engine off and back on--but that didn't seem to have any effect, the system remained broken. I was able to use the rear view camera on the reviewer mirror--but the normal backup cameras remained non-functioning. I promptly tried opening the camera settings again to reset all of the brightness, contrast, tone, color, and black level settings to the default values... but still, the preview area was black and no image could seen. I've verified the outside of the vehicle... these cameras are not blocked at all. There was nothing that could've cause these to go dark. I drive the vehicle home (~5 miles), and found the camera still not to be working.
Mfg Campaign: 11534464
Recall Date: Jul 25, 2023
Nissan North America, Inc.
Defect Description:
BACK OVER PREVENTION: WARNINGS
Potential Consequences:
While waiting in a parking lot, I was reviewing the settings available on the lower center display, one of those options was for "Camera." Inside this menu I found and made adjustment for options like brightness, contrast, tint, color, and black level... and while most of those seemed to work well, and I was able to make suitable adjustments to the camera--the tint and color options seemed to have no effect on the image. So, I opted to adjust tint from the default/middle value all the way to the left/lowest value and save the settings. Even then, with that saved, I was able to switch to the camera and could see there was no difference in the image still. I then remained with the vehicle, still parked with the engine idling, waiting another ten minutes or so before preparing to leave. When I put my vehicle in reverse gear, I was shocked to see that the camera displays had gone completely black. I could no longer see the rear images when backing up. I tried going back to park and again to the rear setting--still, there was no image being displayed for the cameras. I could see some items on-screen still, like the button to switch camera views and to toggle the parking sensors on/off. When switching camera views/angles, the system would continue displaying the same two black/empty displays. I tried turning the engine off and back on--but that didn't seem to have any effect, the system remained broken. I was able to use the rear view camera on the reviewer mirror--but the normal backup cameras remained non-functioning. I promptly tried opening the camera settings again to reset all of the brightness, contrast, tone, color, and black level settings to the default values... but still, the preview area was black and no image could seen. I've verified the outside of the vehicle... these cameras are not blocked at all. There was nothing that could've cause these to go dark. I drive the vehicle home (~5 miles), and found the camera still not to be working.
Corrective Action:
While waiting in a parking lot, I was reviewing the settings available on the lower center display, one of those options was for "Camera." Inside this menu I found and made adjustment for options like brightness, contrast, tint, color, and black level... and while most of those seemed to work well, and I was able to make suitable adjustments to the camera--the tint and color options seemed to have no effect on the image. So, I opted to adjust tint from the default/middle value all the way to the left/lowest value and save the settings. Even then, with that saved, I was able to switch to the camera and could see there was no difference in the image still. I then remained with the vehicle, still parked with the engine idling, waiting another ten minutes or so before preparing to leave. When I put my vehicle in reverse gear, I was shocked to see that the camera displays had gone completely black. I could no longer see the rear images when backing up. I tried going back to park and again to the rear setting--still, there was no image being displayed for the cameras. I could see some items on-screen still, like the button to switch camera views and to toggle the parking sensors on/off. When switching camera views/angles, the system would continue displaying the same two black/empty displays. I tried turning the engine off and back on--but that didn't seem to have any effect, the system remained broken. I was able to use the rear view camera on the reviewer mirror--but the normal backup cameras remained non-functioning. I promptly tried opening the camera settings again to reset all of the brightness, contrast, tone, color, and black level settings to the default values... but still, the preview area was black and no image could seen. I've verified the outside of the vehicle... these cameras are not blocked at all. There was nothing that could've cause these to go dark. I drive the vehicle home (~5 miles), and found the camera still not to be working.
Additional Notes:
While waiting in a parking lot, I was reviewing the settings available on the lower center display, one of those options was for "Camera." Inside this menu I found and made adjustment for options like brightness, contrast, tint, color, and black level... and while most of those seemed to work well, and I was able to make suitable adjustments to the camera--the tint and color options seemed to have no effect on the image. So, I opted to adjust tint from the default/middle value all the way to the left/lowest value and save the settings. Even then, with that saved, I was able to switch to the camera and could see there was no difference in the image still. I then remained with the vehicle, still parked with the engine idling, waiting another ten minutes or so before preparing to leave. When I put my vehicle in reverse gear, I was shocked to see that the camera displays had gone completely black. I could no longer see the rear images when backing up. I tried going back to park and again to the rear setting--still, there was no image being displayed for the cameras. I could see some items on-screen still, like the button to switch camera views and to toggle the parking sensors on/off. When switching camera views/angles, the system would continue displaying the same two black/empty displays. I tried turning the engine off and back on--but that didn't seem to have any effect, the system remained broken. I was able to use the rear view camera on the reviewer mirror--but the normal backup cameras remained non-functioning. I promptly tried opening the camera settings again to reset all of the brightness, contrast, tone, color, and black level settings to the default values... but still, the preview area was black and no image could seen. I've verified the outside of the vehicle... these cameras are not blocked at all. There was nothing that could've cause these to go dark. I drive the vehicle home (~5 miles), and found the camera still not to be working.
Mfg Campaign: 11534464
Recall Date: Jul 25, 2023
Nissan North America, Inc.
Defect Description:
FORWARD COLLISION AVOIDANCE: AUTOMATIC EMERGENCY BRAKING
Potential Consequences:
Vehicle aggressively and without cause engaged the Automatic Emergency Braking System causing the driver to be slammed against her seat belt and almost having the car in back of us to almost rear end our vehicle. This has happened in the past but it has been a manageable slight deceleration when going around a gentle curve or at the railroad overpass. . This time the incident was intense almost causing a rear end collision. I would add that this severe incident happened when approaching the same railroad overpass in the rain. This has also happened at this intersection in good weather. Under all circumstances there were no obstructions I front of the vehicle. I have read that this problem has occurred in earlier years of Nissan products. In all instances the appropriate system warning light illuminated.
Corrective Action:
Vehicle aggressively and without cause engaged the Automatic Emergency Braking System causing the driver to be slammed against her seat belt and almost having the car in back of us to almost rear end our vehicle. This has happened in the past but it has been a manageable slight deceleration when going around a gentle curve or at the railroad overpass. . This time the incident was intense almost causing a rear end collision. I would add that this severe incident happened when approaching the same railroad overpass in the rain. This has also happened at this intersection in good weather. Under all circumstances there were no obstructions I front of the vehicle. I have read that this problem has occurred in earlier years of Nissan products. In all instances the appropriate system warning light illuminated.
Additional Notes:
Vehicle aggressively and without cause engaged the Automatic Emergency Braking System causing the driver to be slammed against her seat belt and almost having the car in back of us to almost rear end our vehicle. This has happened in the past but it has been a manageable slight deceleration when going around a gentle curve or at the railroad overpass. . This time the incident was intense almost causing a rear end collision. I would add that this severe incident happened when approaching the same railroad overpass in the rain. This has also happened at this intersection in good weather. Under all circumstances there were no obstructions I front of the vehicle. I have read that this problem has occurred in earlier years of Nissan products. In all instances the appropriate system warning light illuminated.
Mfg Campaign: 11463241
Recall Date: May 3, 2022
Nissan North America, Inc.
Defect Description:
FUEL SYSTEM, GASOLINE
Potential Consequences:
The contact owns a 2020 Infiniti QX80. The contact received notification of NHTSA Campaign Number: 21V373000 (Fuel System, Gasoline) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The local dealer and the manufacturer were made aware of the issue. The contact had experienced a failure where the vehicle would not start as needed. The contact related the failure to the recall. Parts distribution disconnect. The failure mileage was not available.
Corrective Action:
The contact owns a 2020 Infiniti QX80. The contact received notification of NHTSA Campaign Number: 21V373000 (Fuel System, Gasoline) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The local dealer and the manufacturer were made aware of the issue. The contact had experienced a failure where the vehicle would not start as needed. The contact related the failure to the recall. Parts distribution disconnect. The failure mileage was not available.
Additional Notes:
The contact owns a 2020 Infiniti QX80. The contact received notification of NHTSA Campaign Number: 21V373000 (Fuel System, Gasoline) however, the part to do the recall repair was not yet available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The local dealer and the manufacturer were made aware of the issue. The contact had experienced a failure where the vehicle would not start as needed. The contact related the failure to the recall. Parts distribution disconnect. The failure mileage was not available.
Mfg Campaign: 11446157
Recall Date: Jan 4, 2022
Nissan North America, Inc.
Defect Description:
VEHICLE SPEED CONTROL
Potential Consequences:
THE CRUISE CONTROL IS VERY ABRUPTED WHEN ENGAGING THE RESUME FEATURE. THE CRUISE WILL CAUSE THE TRANSMISSION TO DOWNSHIFT AND ENGINE TO REV ABOVE 5000 RPMS FOR JUST A COUPLE OF MPH SPEED INCREASE. I BELIEVE THIS A DESIGN FLAW THAT COULD CAUSE A DRIVER TO LOSE CONTROL OF THE CAR.
Corrective Action:
THE CRUISE CONTROL IS VERY ABRUPTED WHEN ENGAGING THE RESUME FEATURE. THE CRUISE WILL CAUSE THE TRANSMISSION TO DOWNSHIFT AND ENGINE TO REV ABOVE 5000 RPMS FOR JUST A COUPLE OF MPH SPEED INCREASE. I BELIEVE THIS A DESIGN FLAW THAT COULD CAUSE A DRIVER TO LOSE CONTROL OF THE CAR.
Additional Notes:
THE CRUISE CONTROL IS VERY ABRUPTED WHEN ENGAGING THE RESUME FEATURE. THE CRUISE WILL CAUSE THE TRANSMISSION TO DOWNSHIFT AND ENGINE TO REV ABOVE 5000 RPMS FOR JUST A COUPLE OF MPH SPEED INCREASE. I BELIEVE THIS A DESIGN FLAW THAT COULD CAUSE A DRIVER TO LOSE CONTROL OF THE CAR.
Mfg Campaign: 11337507
Recall Date: Jul 5, 2020
Need Legal Help?
Featured Attorneys
Barry Edzant
Edzant Price LLC
Valencia, CA • 36 yrs
Focus: Lemon Law, Personal Injury