Complaints & Recalls
Official Safety Recalls - Important!
35 RecallsThese are official manufacturer recalls ordered by NHTSA for safety defects. If you own this vehicle, contact your dealer immediately for free repairs.
Toyota Motor Engineering & Manufacturing
Safety Issue:
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022-2025 Toyota Tundra and Tundra Hybrid vehicles. Moisture may enter the reverse light assemblies and cause a light failure.
Potential Risk:
FREE Recall Solution:
Mfg Campaign: 25TB06 / 25TA06
Toyota Motor Engineering & Manufacturing
Safety Issue:
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022-2023 Tundra and Lexus LX600 vehicles equipped with a V35A engine. Debris from the manufacturing process may contaminate the engine and cause the main bearings to fail, which can result in an engine stall and loss of drive power.
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Mfg Campaign: 24TB07,24TA07,24LB04
Recall Date: May 30, 2024
Toyota Motor Engineering & Manufacturing
Safety Issue:
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022-2024 Tundra, Tundra Hybrid, Lexus LX600, and 2023-2024 Sequoia Hybrid vehicles. Unexpected vehicle movement may occur when the vehicle is in neutral and the brakes are not applied.
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Mfg Campaign: 24TA02, 24LA02
Recall Date: Feb 21, 2024
Southeast Toyota Distributors, Llc
Safety Issue:
Southeast Toyota Distributors, LLC (SET) is recalling certain 2022-2024 Toyota Tundra vehicles. The load carrying capacity modification label states the incorrect load carrying capacity, which can result in an overloaded vehicle. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 110, "Tire Selection and Rims."
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.safercar.gov.
Mfg Campaign: SET23B
Recall Date: Nov 9, 2023
Toyota Motor Engineering & Manufacturing
Safety Issue:
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022-2023 Tundra and Tundra Hybrid vehicles. The plastic fuel tube routed near metallic brake lines may chafe against the brake lines and become damaged, possibly resulting in a fuel leak.
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Mfg Campaign: 23TB09 / 23TA09
Recall Date: Aug 10, 2023
Toyota Motor Engineering & Manufacturing
Safety Issue:
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022-2023 Tundra and Tundra Hybrid vehicles that may be equipped with a Toyota genuine accessory tonneau cover. The tonneau cover attachment joints may come loose and allow the cover to detach.
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Mfg Campaign: 23TB03 / 23TA03
Recall Date: Mar 3, 2023
Toyota Motor Engineering & Manufacturing
Safety Issue:
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022-2023 Tundra and Tundra Hybrid vehicles. A software error in the combination meter's electronic control unit (ECU) may cause the Instrument Panel LCD display to go blank. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 101, "Control and Displays."
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Mfg Campaign: 23TA02
Recall Date: Feb 22, 2023
Toyota Motor Engineering & Manufacturing
Safety Issue:
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022 Lexus NX250, NX350, and Toyota Tundra vehicles. The Skid Control ECU within the Brake Actuator Assembly may falsely detect an overcurrent condition of the Electronic Parking Brake (EPB) Actuator and enter a failsafe mode which prevents the EPB from being engaged. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 135, "Light Vehicle Brake Systems."
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Mfg Campaign: 22TA11 and 22LA04
Recall Date: Sep 1, 2022
Toyota Motor Engineering & Manufacturing
Safety Issue:
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022 Tundra and Tundra Hybrid vehicles equipped with a Panoramic View Monitor (PVM) system. Incorrect programming of the parking-assist electronic control unit (ECU) software, may cause the front camera image to appear on the multimedia display instead of the rear camera image when the shifter is placed into reverse. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Mfg Campaign: 22TA07
Recall Date: Jul 13, 2022
Toyota Motor Engineering & Manufacturing
Safety Issue:
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022 Tundra and Tundra Hybrid vehicles. The flange nuts on the axle shaft sub-assemblies can loosen over time and potentially cause one or both axle shaft sub-assemblies to separate from the axle housing.
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Mfg Campaign: 22TA05
Recall Date: Jun 23, 2022
Toyota Motor Engineering & Manufacturing
Safety Issue:
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2022 Tundra vehicles equipped with a Panoramic View Monitor (PVM) system. The parking assist electronic control unit (ECU) software may prevent transmission of the rearview camera signal during cold weather, preventing the rearview image from displaying. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard number 111, "Rear Visibility."
Potential Risk:
FREE Recall Solution:
Additional Details:
Owners may also contact the National Highway Traffic Safety Administration Vehicle Safety Hotline at 1-888-327-4236 (TTY 1-800-424-9153), or go to www.nhtsa.gov.
Mfg Campaign: 22TA04
Recall Date: Apr 28, 2022
Consumer Complaints
452 ComplaintsToyota Motor Corporation
Defect Description:
SEATS
Potential Consequences:
Since around 35,000 miles, the 10-way Power Adjustable Driver's Seat makes a terrible squeaky sound when going over any bumps in the road. If the Driver were to move while in the seat, the squeak is present. We have already paid out of pocket (not considered a warranty issue because nothing is "broken"), but the squeak has returned. This is no fault of the dealership, but because of the design that Toyota implemented for just the 10-way Power Adjustable Driver's Seat. If we reduce the Lumbar Support down to its lowest setting, the squeak gets better but it makes the seat that much more uncomfortable. These are the worst seats we've ever had in any vehicle, let alone a Toyota/Lexus product.
Corrective Action:
Since around 35,000 miles, the 10-way Power Adjustable Driver's Seat makes a terrible squeaky sound when going over any bumps in the road. If the Driver were to move while in the seat, the squeak is present. We have already paid out of pocket (not considered a warranty issue because nothing is "broken"), but the squeak has returned. This is no fault of the dealership, but because of the design that Toyota implemented for just the 10-way Power Adjustable Driver's Seat. If we reduce the Lumbar Support down to its lowest setting, the squeak gets better but it makes the seat that much more uncomfortable. These are the worst seats we've ever had in any vehicle, let alone a Toyota/Lexus product.
Additional Notes:
Since around 35,000 miles, the 10-way Power Adjustable Driver's Seat makes a terrible squeaky sound when going over any bumps in the road. If the Driver were to move while in the seat, the squeak is present. We have already paid out of pocket (not considered a warranty issue because nothing is "broken"), but the squeak has returned. This is no fault of the dealership, but because of the design that Toyota implemented for just the 10-way Power Adjustable Driver's Seat. If we reduce the Lumbar Support down to its lowest setting, the squeak gets better but it makes the seat that much more uncomfortable. These are the worst seats we've ever had in any vehicle, let alone a Toyota/Lexus product.
Mfg Campaign: 11595424
Recall Date: Jun 20, 2024
Toyota Motor Corporation
Defect Description:
SEATS
Potential Consequences:
Driver's Seat appears to have some play in it where when accelerating or coming to a stop, the seat bottom will move forward and/or backwards. This has continued to happen and after repeated attempts to have the dealer resolve it, they have basically told me it was designed that way. We've never had another Toyota product do this. We do understand there are certain specifications needed to meet safety requirements, but we've sat and driven in other models of the same specifications and their seats do not do this.
Corrective Action:
Driver's Seat appears to have some play in it where when accelerating or coming to a stop, the seat bottom will move forward and/or backwards. This has continued to happen and after repeated attempts to have the dealer resolve it, they have basically told me it was designed that way. We've never had another Toyota product do this. We do understand there are certain specifications needed to meet safety requirements, but we've sat and driven in other models of the same specifications and their seats do not do this.
Additional Notes:
Driver's Seat appears to have some play in it where when accelerating or coming to a stop, the seat bottom will move forward and/or backwards. This has continued to happen and after repeated attempts to have the dealer resolve it, they have basically told me it was designed that way. We've never had another Toyota product do this. We do understand there are certain specifications needed to meet safety requirements, but we've sat and driven in other models of the same specifications and their seats do not do this.
Mfg Campaign: 11595427
Recall Date: Jun 20, 2024
Toyota Motor Corporation
Defect Description:
ELECTRICAL SYSTEM
Potential Consequences:
The Digital Instrument Cluster continues to have freezing and lagging while in motion. The DTE (Distance To Empty) has reset itself in the midst of driving with no input from the driver. This has continued to happen for multiple months. Also, the Fuel Gauge has become stuck. Toyota did release a TSB (T-SB-0022-23) to "resolve" this issue but it continues to be an issue well into the 2024 model year.
Corrective Action:
The Digital Instrument Cluster continues to have freezing and lagging while in motion. The DTE (Distance To Empty) has reset itself in the midst of driving with no input from the driver. This has continued to happen for multiple months. Also, the Fuel Gauge has become stuck. Toyota did release a TSB (T-SB-0022-23) to "resolve" this issue but it continues to be an issue well into the 2024 model year.
Additional Notes:
The Digital Instrument Cluster continues to have freezing and lagging while in motion. The DTE (Distance To Empty) has reset itself in the midst of driving with no input from the driver. This has continued to happen for multiple months. Also, the Fuel Gauge has become stuck. Toyota did release a TSB (T-SB-0022-23) to "resolve" this issue but it continues to be an issue well into the 2024 model year.
Mfg Campaign: 11595429
Recall Date: Jun 20, 2024
Toyota Motor Corporation
Defect Description:
ENGINE
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Mfg Campaign: 11595349
Recall Date: Jun 19, 2024
Toyota Motor Corporation
Defect Description:
POWER TRAIN
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Mfg Campaign: 11595349
Recall Date: Jun 19, 2024
Toyota Motor Corporation
Defect Description:
FUEL/PROPULSION SYSTEM
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Mfg Campaign: 11595349
Recall Date: Jun 19, 2024
Toyota Motor Corporation
Defect Description:
ENGINE
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Mfg Campaign: 11595350
Recall Date: Jun 19, 2024
Toyota Motor Corporation
Defect Description:
FUEL/PROPULSION SYSTEM
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Mfg Campaign: 11595350
Recall Date: Jun 19, 2024
Toyota Motor Corporation
Defect Description:
POWER TRAIN
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modified to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into traffic in slower moving city streets. There are members of an online forum who have been able to record the data flow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10-AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/Sequoia).
Mfg Campaign: 11595350
Recall Date: Jun 19, 2024
Toyota Motor Corporation
Defect Description:
ENGINE
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Mfg Campaign: 11595355
Recall Date: Jun 19, 2024
Toyota Motor Corporation
Defect Description:
FUEL/PROPULSION SYSTEM
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Mfg Campaign: 11595355
Recall Date: Jun 19, 2024
Toyota Motor Corporation
Defect Description:
POWER TRAIN
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Mfg Campaign: 11595355
Recall Date: Jun 19, 2024
Toyota Motor Corporation
Defect Description:
ENGINE
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Mfg Campaign: 11595357
Recall Date: Jun 19, 2024
Toyota Motor Corporation
Defect Description:
FUEL/PROPULSION SYSTEM
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Mfg Campaign: 11595357
Recall Date: Jun 19, 2024
Toyota Motor Corporation
Defect Description:
POWER TRAIN
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Mfg Campaign: 11595357
Recall Date: Jun 19, 2024
Toyota Motor Corporation
Defect Description:
ENGINE
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Mfg Campaign: 11595362
Recall Date: Jun 19, 2024
Toyota Motor Corporation
Defect Description:
FUEL/PROPULSION SYSTEM
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Mfg Campaign: 11595362
Recall Date: Jun 19, 2024
Toyota Motor Corporation
Defect Description:
POWER TRAIN
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Mfg Campaign: 11595362
Recall Date: Jun 19, 2024
Toyota Motor Corporation
Defect Description:
FUEL/PROPULSION SYSTEM
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Mfg Campaign: 11595363
Recall Date: Jun 19, 2024
Toyota Motor Corporation
Defect Description:
ENGINE
Potential Consequences:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Corrective Action:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Additional Notes:
At certain times, when coming to a stop, and then attempting to proceed, the throttle with delay or lag from a stop. This has happened since the start of ownership in Feb 2022 up until today. Toyota has issued on previous Technical Service Bulletin (TSB) - T-SB-0111-22 - that Toyota states should resolve an issue with "Hesitation From Stop and Surge Concerns". The TCM -Transmission Control Module - logic has been modiWed to address these conditions. According to Toyota, this updated logic SHOULD keep this from happening. This TSB was released December 16, 2022. To date, this issue continues to occur. The only way to keep it from happening is to Reset the TCM Learning. This requires the battery to be unplugged for an extended period of time. There was a subsequent TCM logic update for Recall 24TA02 (NHTSA Campaign Number 24V125000). It would seem that this TCM Logic Update has actually caused this condition to be present more often. This is something that we have expressed to our Service Consultant at every visit and it is still occurring over two years later. We have had this happen multiple times while attempting to proceed through a 4-way stop, as well as trying to merge into tra`c in slower moving city streets. There are members of an online forum who have been able to record the data aow and show when and how the delay occurs. Other than December 2022 TSB, Toyota has not acknowledged this issue even though it continues to occur on the MY22+ Tundra/MY23+ Sequoia, as well as the MY18+ Lexus LS 500. I am lead to believe this is a result of the programming for the Direct Shift 10- AT from Aisin/Toyota and/or the V35A-FTS, both Type '17 (LS 500) and the Type '21 (Tundra/ Sequoia).
Mfg Campaign: 11595363
Recall Date: Jun 19, 2024
Need Legal Help?
Featured Attorneys
Barry Edzant
Edzant Price LLC
Valencia, CA • 36 yrs
Focus: Lemon Law, Personal Injury